Script was working perfectly running D700, D810, and D500 Friday and Saturday using 1.8.6v1. But today started having the D810 fail during either of two up/down ramps during totality. I have downloaded 1.8.6v2 but still the same behavior.
When I quit the program after the script completes I sometimes get the following in the console - this just a snippet at the end (I tried to attach a .txt of the whole console file but it was not permitted).
Aug 14 21:04:05 Solar Eclipse Maestro[7448] <Info>: SIML +0.0s ISO 200 1/15 s f/6.3 RAW D810 24 shot rndtrip ramp to 1 sec (24 frames at 1.0 stop)
Aug 14 21:04:05 Solar Eclipse Maestro[7448] <Info>: SIML +0.0s ISO 100 1/8 s f/5.6 RAW D500 26 shot rndtrip ramp to 2 sec (26 frames at 1.0 stop)
Aug 14 21:04:05 Solar Eclipse Maestro[7448] <Info>: Camera #1: image/video added [0xFFFFFFFF-0x091F0935]
Aug 14 21:04:05 Solar Eclipse Maestro[7448] <Info>: Camera #1: capture complete [0x0000033B]
Aug 14 21:04:05 Solar Eclipse Maestro[7448] <Info>: Camera #2: image/video added [0xFFFFFFFF-0x0A1C6121]
Aug 14 21:04:05 Solar Eclipse Maestro[7448] <Info>: Camera #2: capture complete [0x000003FB]
Aug 14 21:04:06 Solar Eclipse Maestro[7448] <Info>: SIML +0.0s ISO 100 1/4 s f/5.6 RAW D500 26 shot rndtrip ramp to 2 sec (26 frames at 1.0 stop)
Aug 14 21:04:06 Solar Eclipse Maestro[7448] <Info>: SIML +0.0s ISO 200 1/8 s f/6.3 RAW D810 24 shot rndtrip ramp to 1 sec (24 frames at 1.0 stop)
Aug 14 21:04:06 Solar Eclipse Maestro[7448] <Info>: Camera #1: image/video added [0xFFFFFFFF-0x091F0936]
Aug 14 21:04:06 Solar Eclipse Maestro[7448] <Info>: Camera #1: capture complete [0x00000341]
Aug 14 21:04:06 Solar Eclipse Maestro[7448] <Info>: Camera #2: image/video added [0xFFFFFFFF-0x0A1C6122]
Aug 14 21:04:06 Solar Eclipse Maestro[7448] <Info>: Camera #2: capture complete [0x00000402]
Aug 14 21:04:07 Solar Eclipse Maestro[7448] <Info>: Camera #1: image/video added [0xFFFFFFFF-0x091F0937]
Aug 14 21:04:07 Solar Eclipse Maestro[7448] <Info>: Camera #1: capture complete [0x00000345]
Aug 14 21:04:07 Solar Eclipse Maestro[7448] <Info>: Camera #2: image/video added [0xFFFFFFFF-0x0A1C6123]
Aug 14 21:04:07 Solar Eclipse Maestro[7448] <Info>: Camera #2: capture complete [0x00000408]
Aug 14 21:05:47 Solar Eclipse Maestro[7448] <Info>: Camera thread #3 ended
Aug 14 21:05:47 Solar Eclipse Maestro[7448] <Info>: Camera thread #4 ended
Aug 14 21:06:48 Solar Eclipse Maestro[7448] <Notice>: Shutter speed camera #2 not set to: 1/4s (line #119 - Undefined Response) at 03:06:48.4 UT
Aug 14 21:06:48 Solar Eclipse Maestro[7448] <Notice>: Error 'Undefined Response' while taking ramps up and down picture #10 on camera #2 'D810' (line #119)
Aug 14 21:06:48 Solar Eclipse Maestro[7448] <Info>: *** Stopped SEM 1.8.6v2 Intel ICC ***
In this case both cameras stopped firing. Most of the time I get no <Notice> message the program just quits and puts up the crash dialog to send to Apple.
"Undefined response" is the key message when it does report. I do not get Device Busy. Is this some sort of communication collision or error? If I run each camera alone in a D500 or D800 script no failures in half a dozen runs, but have not been successful in completing a run with both cameras in the script. I have purposely not given commands at the same time. I tried to attach the script and two console outputs one in which both cameras stopped and one in which the D810 stopped but the D500 completed, but .txt was not allowed. I am semi panicked and thinking about using only one camera. Any help appreciated. I haven't changed any hardware including cables.
Bob